David Hedges

Image

I make a few CF frames mostly for personal use :)

.....
Image

The Dave Store

Visit Store

Kits

  • Kit
    More Details

    Freestyler

    $ 39.10
  • Kit
    More Details

    3 and a Half Inch Micro PLUS Configuration

    $ 20.90

    Very tight build - trying to keep things as light as possible. Not much space here so ensure your gear will fit :)

    'PLUS'  Configuration - so I can run the props closer to the stack. Yes X is probably more efficient but yeah....

    Designed to work with 3.5'' props

    20 x 20 Stack (for Micro FC/4in1/etc) offset 45 degrees for space savings

    Motor pattern: M2 (12mm)  e.g. Brotherhobby 1407

    Fits a few VTX / Cameras. Easiest is the eachine VTX/Camera AIO but you can also fit a Runcam Micro with a small VTX if you can get your other gear to fit. A 3d printed cam holder might help here.

    Frame is tough- no flex should last.

Products

  • product
    More Details

    3MM JC MEMORIAL PROP TOOL FOR M5

    $ 3.08

    As most of you know, William James (JC) Culpepper "Project Blue Falcon" passed away suddenly in a motorcycle accident on 29 June 2017. 

    I never knew JC personally outside a Facebook messages, helping me out with technical problems on my quads, JC was always super helpful sharing his time with me and others in the FPV hobby. I learnt so much from his YouTube instructional videos and he made my life a lot easier as he went into a lot more detail than most. The world truly is a worse place without you - both in the FPV hobby and without very special people like you.

    For those that are interested, I designed this Carbon Fibre Prop Tool, just something small to remember JC by. It may need some finishing with sandpaper to clean up any dust (do this in running water so you don't breathe in the CF)

    I'm obviously not adding any commission to this (apart from what armattan / CNC cutters make).

    Note: At this stage, I haven't received one so not sure how strong it is but I believe it should be pretty tough. 

    This tool is for M5 motors. I can add M4 if people are interested.

  • product
    More Details

    5mm JC Memorial Prop Tool for M5

    $ 2.94

    As most of you know, William James (JC) Culpepper "Project Blue Falcon" passed away suddenly in a motorcycle accident on 29 June 2017. 

    I never knew JC personally outside a Facebook messages, helping me out with technical problems on my quads, JC was always super helpful sharing his time with me and others in the FPV hobby. I learnt so much from his YouTube instructional videos and he made my life a lot easier as he went into a lot more detail than most. The world truly is a worse place without you - both in the FPV hobby and without very special people like you.

    For those that are interested, I designed this Carbon Fibre Prop Tool, just something small to remember JC by. It may need some finishing with sandpaper to clean up any dust (do this in running water so you don't breathe in the CF)

    I'm obviously not adding any commission to this (apart from what armattan / CNC cutters make).

    Note: At this stage, I haven't received one so not sure how strong it is but I believe it should be pretty tough. 

    This tool is for M5 motors. I can add M4 if people are interested.

  • product
    More Details

    JC Memorial Keyring

    $ 2.94

    As most of you know, William James (JC) Culpepper "Project Blue Falcon" passed away suddenly in a motorcycle accident on 29 June 2017. 

    I never knew JC personally outside a Facebook messages, helping me out with technical problems on my quads, JC was always super helpful sharing his time with me and others in the FPV hobby. I learnt so much from his YouTube instructional videos and he made my life a lot easier as he went into a lot more detail than most. The world truly is a worse place without you - both in the FPV hobby and without very special people like you.

    For those that are interested, I designed this Carbon Fibre Keyring, just something small to remember JC by. It may need some finishing with sandpaper to clean up any dust (do this in running water so you don't breathe in the CF)

    I'm obviously not adding any commission to this (apart from what armattan / CNC cutters make).

    Note: At this stage, I haven't received one so not sure how strong it is but I believe it should be pretty tough.